WARM GLASS KILN STUDIOLast reviewed: 2026-11-19

Fused Glass COE 90 vs. COE 96 Firing Schedule Planner

Quick answer: For standard 6 mm two-layer fused glass, ramp at 300 F/hr to a 1225-1250 F bubble squeeze for 30 minutes, climb to 1350-1375 F for tack, 1400-1425 F for contour, or 1450-1480 F for full fuse, then rapid-cool to the 900 F (COE 90) or 950 F (COE 96) anneal hold.

Interactive 6-Segment Glass Kiln Curve & Anneal Calculator COE 90 & COE 96 SCHEDULER
Glass System (90=Bullseye, 96=Oceanside)90 COE
Total Glass Thickness6 mm
Piece Width / Span10 in
Process Peak & Hold
--
Anneal Soak Temp
--
Total Firing Cycle
--
Ready

What Materials, Cost, Time, and Skill Level Do You Need?

Estimated Cost
$1.80 - $4.50 kiln electricity / firing
Active + Cure Time
7 - 16 hours full ramp & cool
Skill Difficulty
Intermediate
Peak Craft Window
Jan - Mar 2027 Studio Prep

Core Supplies & Tooling Checklist

What Safety Rules Should You Follow Before Starting?

Follow your product's own label/SDS instructions where brands differ.

Why Can You Never Mix COE 90 and COE 96 Glass?

Coefficient of Expansion (COE) measures how many ten-millionths of a unit a glass expands or contracts per degree Celsius as it heats and cools. Bullseye tested-compatible glass is formulated around COE 90 (90 x 10^-7 / C), whereas Oceanside and Spectrum System 96 target COE 96 (96 x 10^-7 / C). On a bench they look identical, yet during cooling from liquid melt back down to room temperature, COE 96 contracts roughly 6.7% more than COE 90.

When two incompatible glasses fuse together above 1300 F, they bond while molten and stress-free. As the kiln drops below the strain point, the COE 96 layer tries to shrink faster than the COE 90 layer, locking permanent tensile and compressive forces across the bond line. Thin test tiles might survive for days before snapping in half from a minor bump or ambient temperature swing.

To prevent studio mix-ups, store COE 90 and COE 96 sheets in separate color-coded bins, label scrap jars immediately after cutting, and never trust unmarked mystery glass from thrift packs or window panes. Window float glass sits near COE 82-87 and reacts unpredictably with both studio fusing lines.

Studio Compatibility RuleEven within a single COE system, test heavy opaque reds, yellows, and sulfur-reactive combinations on a small 2x2 inch scrap tile before committing an expensive platter.

How Do Standard COE 90 and COE 96 Firing Schedules Compare?

Firing ProcessCOE 90 Peak (Hold)COE 96 Peak (Hold)Anneal Soak (6 mm)Visual & Structural Result
Tack Fuse1350-1375 F (10 min)1340-1365 F (10 min)900 F / 950 F (60 min)Crisp edges, high relief, secure point bonds
Contour Fuse1400-1425 F (10 min)1390-1415 F (10 min)900 F / 950 F (60 min)Rounded pillowed edges with visible layer depth
Full Fuse1465-1480 F (10 min)1450-1465 F (10 min)900 F / 950 F (60 min)Single flat 6 mm sheet with smooth fused surface
Slump into Mold1225-1260 F (15 min)1210-1245 F (15 min)900 F / 950 F (60 min)Conforms gently to bisque or stainless mold contour
Fire Polish1300-1330 F (5 min)1285-1315 F (5 min)900 F / 950 F (60 min)Removes coldworking satin haze without flattening edges

How Do Tack, Contour, and Full Fuse Temperatures Differ?

Glass does not have a single sharp melting point like ice; instead its viscosity drops smoothly across a working range. In a tack fuse (1350-1375 F), glass pieces soften just enough to stick firmly at contact points while keeping crisp cut edges, raised relief height, and dimensional frit texture.

A contour fuse (1400-1425 F) softens edges into gentle rounded pillows while preserving visible layer steps and surface topography. It is the preferred target for layered landscapes, tacked stringers that need smooth fingertips, and textured bowls prior to slumping.

A full fuse (1450-1480 F) lowers viscosity until gravity and surface tension pull stacked layers into a single flat 6 mm disk with rounded edges. Because COE 96 melts slightly softer than COE 90 at equivalent temperatures, its peak targets sit 10-15 F lower on average. Holding too long above 1480 F invites devitrification, a cloudy crystalline scum caused by surface crystallization.

Surface Tension EquilibriumUnconfined molten glass naturally pulls toward 6 mm (1/4 inch) thickness. A 3 mm single sheet shrinks inward to thicken, whereas a 12 mm stack spreads outward unless dammed.

What Does Each Segment in a 6-Segment Kiln Schedule Do?

Segment 1 (Initial Ramp, 150-300 F/hr to 1225-1250 F) heats the cold glass slowly enough to prevent thermal shock breakage across the lower temperature zone. Wide plates over 14 inches or thick slabs over 9 mm require slower 150-225 F/hr climbs because kiln corners heat faster than the insulated center.

Holding 20-45 minutes at 1225-1250 F performs the bubble squeeze. At this viscosity, stacked sheets slump together gently from the center outward, pushing trapped air out through the open perimeter before the edges seal shut at higher heat. Skipping the bubble squeeze traps unsightly champagne bubbles inside full-fused blanks.

Segments 2 and 3 sprint quickly (400 F/hr) to the process peak (1350-1480 F) for a short 10-15 minute soak, then drop as fast as possible (AFAP, venting closed or controlled) straight past the 1400-1100 F devitrification danger zone down to the annealing soak temperature.

Kiln Log HabitRecord the actual top temperature, hold minutes, kiln shelf load, and visual outcome in a firing notebook; your kiln's thermocouple placement can shift real glass temperature by 15-25 F.

How Do Anneal Soak Times Scale with Slab Thickness?

Annealing equalizes temperature between the outside skin and the deep core of the glass at its annealing point: 900 F (482 C) for Bullseye COE 90 and 950 F (510 C) for COE 96. Once core and skin reach the exact same temperature, the glass must cool slowly through the annealing range (roughly 150 F below the soak) so no new temperature gradient forms while the glass solidifies permanently.

Annealing time does not scale linearly with thickness; thermal diffusion slows down with the square of thickness. Doubling a fused blank from 6 mm to 12 mm quadruples the internal cooling lag. While a 6 mm two-layer plate needs 60 minutes at 900 F/950 F followed by a 150 F/hr drop to 750 F/800 F, a 12 mm thick slab requires roughly 180 minutes at soak and a much gentler 60-90 F/hr cool.

For large dammed castings over 18 mm, consult Bullseye's thick-slab annealing tables and reduce initial cool rates to 25-40 F/hr. Rushing the final cool below 700 F can still crack wide pieces, so keep the kiln closed until the digital display reads below 120 F.

Polarizing Test CheckView finished clear or translucent pieces between two crossed polarizing films over a light box; bright glowing halo bands reveal trapped strain that calls for a re-anneal cycle.

How Do You Troubleshoot Common Studio Mistakes?

Large trapped air bubbles inside a full-fused plate

Likely Cause: Kiln climbed straight past 1250 F without a bubble squeeze hold, or uneven frit trapped pockets before edges sealed.

Step-by-Step Fix: Insert a 30-45 minute hold at 1225 F (COE 90) or 1240 F (COE 96) with a moderate 250-300 F/hr initial ramp, and place smaller glass pieces toward the center so air escapes outward.

Cloudy white film or dull crust on top of clear glass (devitrification)

Likely Cause: Fingerprints, dirty cutting oil residue, or holding too long between 1425 F and 1480 F triggered surface crystallization.

Step-by-Step Fix: Scrub every glass piece with dish soap or 91% isopropyl alcohol before assembly, wear cotton gloves, minimize peak soak to 10 minutes, and apply a thin coat of overglaze spray if re-firing.

Clean hairline crack running straight through a cool piece

Likely Cause: Thermal shock during heating/cooling or too-short anneal soak for thick overlapping areas or wide platters.

Step-by-Step Fix: Measure the thickest overlapping spot with calipers and program both the anneal soak time and initial cool-down ramp for that maximum thickness, not the thin rim.

Glass edges pulled inward into a lumpy dog-bone shape

Likely Cause: Single-layer 3 mm glass was taken to full fuse temperature, where surface tension forces it toward 6 mm equilibrium.

Step-by-Step Fix: Stack two 3 mm layers everywhere for full-fuse blanks, or reduce peak heat to a contour or tack fuse when working with single-layer designs.

Frequently Asked Questions

Can I use a COE 90 schedule for COE 96 glass?

No. While the heat-up and bubble squeeze look similar, COE 96 anneals at 950 F rather than 900 F and reaches full fuse roughly 10-15 F cooler than Bullseye COE 90. Using 900 F to anneal COE 96 leaves the glass below its true annealing point and fails to relieve internal strain.

Why does the kiln ramp down as fast as possible from peak to anneal?

Between 1450 F and 1100 F, molten glass is still soft enough to release stress, but lingering there encourages crystal growth (devitrification) and over-slumping. Rapidly dropping to 900 F or 950 F locks in crisp shape before precision annealing begins.

How long should I wait before opening my glass kiln?

Wait until the digital pyrometer reads 100-120 F or lower, with the kiln naturally cooled to room temperature. Opening the lid at 250 F feels tempting, yet cool studio air striking the hot top surface can snap wide plates cleanly in half.

Does kiln wash or ThinFire fiber paper change the schedule?

ThinFire paper burns off organic binders between 400 F and 800 F, producing mild odor and smoke. Keep the room ventilated during the first ramp and optionally pause 10 minutes at 600 F with peepholes open if firing multiple sheets of fiber paper.

How do I size an anneal schedule when part of my piece is 3 mm and part is 12 mm?

Always calculate ramp rates and annealing soak duration using the thickest overlapping section on the shelf. A 12 mm focal cabochon glued onto a 3 mm base plate still contains a 12 mm thermal core that requires a 12 mm anneal soak.

Related Craft & Studio Tools

Verified Studio References & Sources

Last reviewed: 2026-11-19

Embed or cite this tool

Copy-paste HTML attribution snippet:
Cite as: GemsMakers. "Fused Glass COE 90 & 96 Kiln Schedule Planner." GemsMakers Tools & Calculators, https://gemsmakers.com/kiln-fused-glass-coe90-coe96-schedule-planner.php (accessed 2026-11-19).