LOST-WAX CASTING FOUNDRYLast reviewed: 2026-11-19

Lost-Wax Casting Metal Weight & Sprue Button Calculator

Quick answer: Multiply your trimmed wax weight (including wax sprues) by the ratio of alloy specific gravity to wax density (~0.95): 10.91x for 925 sterling silver (SG 10.36), 13.76x for 14K yellow gold (SG 13.07), 16.40x for 18K gold (SG 15.58), and 22.58x for platinum (SG 21.45), then add 30 to 40% for the crucible sprue button.

Interactive Wax-to-Alloy Specific Gravity & Button Estimator Alloy Charge & Feed Spec
Wax Tree Weight4.5 g
Wax Density (SG)0.95 SG
Sprue Button Reserve35%
Total Crucible Charge
--
Net Piece Metal
--
Sprue Button Mass
--
Ready

How Do Common Jewelry Casting Alloys Compare by Specific Gravity?

Casting AlloySpecific GravityWax Ratio (SG 0.95)5g Wax Net MetalTotal (+35% Button)Approx. Melt Temp
925 Sterling Silver10.3610.91x54.53 g73.61 g893 C (1640 F)
Yellow Brass / Bronze8.458.89x44.47 g60.04 g930 C (1705 F)
14K Yellow Gold13.0713.76x68.79 g92.87 g880 C (1615 F)
14K White Gold (Ni)12.6213.28x66.42 g89.67 g1000 C (1830 F)
18K Yellow Gold15.5816.40x82.00 g110.70 g905 C (1660 F)
Platinum (Pure/950)21.4522.58x112.89 g152.41 g1768 C (3215 F)

What Materials, Cost, Time, and Skill Level Do You Need?

Estimated Cost
$25 - $600+ by alloy
Active + Cure Time
14 hr burnout + cast
Skill Difficulty
Intermediate - Advanced
Peak Craft Window
Jan - Mar 2027 (Studio Casting)

Core Supplies & Tooling Checklist

  • Precision jeweler's digital scale reading to 0.01 g with tare bowl for weighing wax trees and casting grain
  • Machinable blue, green, or purple jeweler's carving wax (SG ~0.94–0.96) plus softer red sprue wax rods (8–12 gauge)
  • Phosphate-bonded or satin-cast gypsum investment powder, distilled water, and vacuum degassing bell jar
  • Perforated stainless steel casting flask, rubber sprue base, and programmable burnout kiln
  • Fresh 50/50 casting grain and clean previously cast sprue buttons (never over-melted brittle scrap)
  • Dedicated ceramic or graphite crucible seasoned for one alloy family only to avoid gold/silver contamination

What Safety Rules Should You Follow Before Starting?

  • Wear dark welding shade #3–#5 goggles, leather foundry apron, and heat-resistant Kevlar gloves whenever melting and pouring molten precious metals.
  • Keep all moisture, wet tongs, and cold damp steel tools far away from molten metal; steam explosions eject liquid metal violently.
  • Ventilate burnout kilns outdoors or through dedicated canopy hoods because melting wax and heated silica investment release hazardous fumes and respirable cristobalite dust.
  • Wear a P100 particulate respirator when weighing dry investment powder or divesting fired flasks.

Follow your product's own label/SDS instructions where brands differ.

How Does Wax-to-Metal Specific Gravity Math Actually Work?

Lost-wax casting swaps a lightweight hydrocarbon model directly for dense molten metal inside an identical plaster cavity. Because volume stays constant (barring tiny wax-to-metal shrinkage), the exact weight of metal required to fill the wax space equals Wax Weight multiplied by (Alloy Specific Gravity / Wax Specific Gravity).

Standard hard carving waxes such as Ferris File-A-Wax blue, green, and purple cluster tightly around 0.94 to 0.96 specific gravity, while softer pink or turquoise injection waxes sit closer to 0.95 to 1.00. Using 0.95 SG as a baseline turns 925 sterling silver (SG 10.36) into a 10.91x multiplier, 14K yellow gold (SG 13.07) into 13.76x, 18K yellow gold (SG 15.58) into 16.40x, and high-density platinum (SG 21.45) into 22.58x.

If your pattern incorporates heavy organic materials like dried twigs, insect wings, or dense resin prints rather than pure wax, check the printed photopolymer density (often 1.12 to 1.18 SG) so you do not under-calculate the metal charge.

Weigh Wax Plus Sprues TogetherAlways weigh the wax model AFTER attaching all feed sprues and air vents, right before mounting onto the rubber sprue base, so the sprue rod mass is included in Net Metal.

Why Do You Need a 30% to 40% Sprue Button Allowance?

Calculating only the exact volume of your ring and its feed sprues is the fastest way to cast an incomplete, porous piece. As molten alloy enters the mold cavity and begins freezing from the outside inward, liquid metal shrinks by roughly 3 to 5% in volume and pulls fresh molten feed from the cone-shaped button above.

Without a generous 30 to 40% hemispherical sprue button sitting hot over the main feed trunk, hydrostatic head pressure drops too early and shrinkage porosity hollows out the thickest ring shoulder right at the sprue junction. Small single-ring flasks often need a full 40% button (or minimum 12 to 15 g silver / 8 g gold) simply to generate enough thermal mass to stay molten long enough.

You do not waste that extra button metal—once pickled, trimmed cleanly from the sprue neck, and scrubbed free of investment residue, clean buttons can be mixed 50/50 with fresh casting grain on future pours.

Minimum Button FloorEven for a tiny 0.8 g wax charm, never pour less than 12 g of sterling silver or 7 g of 14K gold total, or the tiny charge freezes inside the crucible lip before reaching the flask.

How Should You Size and Angle Sprues for Shrink-Free Castings?

A feed sprue must always freeze AFTER the thickest section of the wax model it feeds. Attach a 6- to 8-gauge (3.2 to 4.1 mm) main sprue directly to the thickest part of a signet ring or bezel head at a smooth 45-degree entry angle facing the flow direction—never perpendicular at 90 degrees where molten metal slams into the opposite investment wall.

Use narrower 10- to 12-gauge auxiliary sprues (2.0 to 2.6 mm) to feed secondary thick pads on wide cuffs or intricate multi-part pendants, and flare the sprue attachment into a gentle fillet with warm wax so sharp corners of plaster do not break off under vacuum suction.

Mount models at least 6 to 8 mm away from the outer steel flask wall and 8 to 10 mm below the top open investment rim. Too little investment thickness cracks during centrifugal spin or drops vacuum seal.

Thickest-Point Feed RuleMolten metal freezes thin bands first and thick shoulders last. Feed the thickest cross-section directly so the sprue stays liquid until the entire ring solidifies.

What Alloys, Burnout Temps, and Crucible Habits Improve Yield?

Deoxidized sterling alloys containing tiny additions of germanium or silicon (like Argentium or modern casting sterling) resist oxygen absorption and fire-scale far better than standard 925 silver when torch-melted, though standard 925 grain performs predictably in vacuum casting machines with carbon crucibles.

Maintain separate labeled crucibles for sterling silver, yellow golds, white golds, and platinum. Trace amounts of low-melt silver or bismuth left in a crucible contaminate high-temperature platinum or palladium casts instantly, causing catastrophic intergranular cracking.

Match flask temperature at cast time to the ring's wall thickness: drop flask temperatures lower (around 450–480 C / 850–900 F) for chunky signets to prevent dendritic grain growth and rough surface pitting, while thin filigree warrants warmer 540–600 C (1000–1100 F) flasks so delicate tips fill completely.

Fresh Grain RatioBlend at least 50% new deoxidized casting grain with 50% thoroughly cleaned old buttons to prevent zinc depletion and brittle porosity.

How Do You Troubleshoot Common Studio Mistakes?

Shrunken, pitted craters appear on the ring right where the sprue attaches

Likely Cause: Feed sprue was thinner than the ring shoulder or the sprue button was under 25% of charge weight, freezing prematurely.

Step-by-Step Fix: Increase sprue gauge to 8g (3.2 mm+) on thick pads, flare the wax junction smoothly, and reserve a full 35–40% button weight.

Short fill or rounded-off thin edges on filigree prongs and narrow bands

Likely Cause: Flask temperature or metal casting temperature was too low, or vacuum/centrifugal pressure lacked sufficient head.

Step-by-Step Fix: Increase flask cast temperature by 40–50 C for delicate filigree, add small blind air-vent risers on trapped tips, and verify vacuum seal gaskets.

Tiny spherical metal beads ('flashing' or bubbles) dot the inside of the ring

Likely Cause: Air bubbles clung to the wax pattern during investment pouring due to skipped debubblizer or weak vacuum degassing.

Step-by-Step Fix: Spray wax lightly with alcohol-free debubblizer, vacuum mixed investment for 90 seconds, and vacuum poured flasks for 60 seconds before initial set.

Dark grey rough scale and brittle fractures in recycled sterling castings

Likely Cause: Overheated melt oxidized copper content or reused scrap buttons repeatedly without fresh deoxidized grain.

Step-by-Step Fix: Keep torch flame neutral-reducing, never exceed liquidus temperature by more than 100 C, and maintain at least 50% fresh grain per batch.

Frequently Asked Questions

Should I weigh the wax model before or after adding sprues?

Weigh the wax model AFTER attaching all feed sprues so the metal multiplier accounts for both your ring and the feed channels, then add 30 to 40% on top for the sprue cone button.

What specific gravity do blue and green carving waxes have?

Standard machinable carving waxes (Ferris blue, green, and purple) have a specific gravity between 0.93 and 0.96, so 0.95 is the universal studio baseline.

Why does 18K gold require so much more weight than 925 sterling silver?

Gold has a much higher atomic density (15.58 SG for 18K yellow vs 10.36 SG for sterling). The exact same ring wax requires about 50% more grams of 18K gold to fill the identical mold volume.

Can I cast 100% recycled sprue buttons without new grain?

Recycling 100% buttons repeatedly burns out deoxidizers and zinc, leading to gas porosity and brittle metal. Always blend at least 50% fresh casting grain with clean, pickled buttons.

How does 3D-printed castable resin change the weight calculation?

Castable photopolymer resins usually have a specific gravity around 1.12 to 1.18 rather than 0.95, so dividing metal SG by 1.15 gives a slightly lower multiplier (~9.0x for sterling instead of 10.9x).

What water-to-investment ratio prevents surface flashing during burnout?

Most satin-cast gypsum investments perform best at a strict 38 to 40 mL of room-temperature distilled water per 100 g of powder, mixed for 3.5 minutes, vacuumed, and held at a 150 C (300 F) steam-dewax hold before ramping to 730 C (1350 F).

Related Craft & Studio Tools

Verified Studio References & Sources

Last reviewed: 2026-11-19

Embed or cite this tool

Copy-paste HTML attribution snippet:
Cite as: GemsMakers. "Lost-Wax Casting Weight & Sprue Button Calculator." GemsMakers Tools & Calculators, https://gemsmakers.com/lost-wax-jewelry-spruing-casting-weight-tool.php (accessed 2026-11-19).